A front-load washer that shakes or walks across the floor during spin is usually not level. Adjust the four feet, lock them with their nuts and check the floor for flex. If it still walks, look for leftover shipping bolts, worn shock absorbers or an unbalanced load. Fix it soon, because walking can loosen hoses.
Why does my washer shake or walk during the spin cycle?
A front-load washer that vibrates noticeably or shifts across the floor during its spin is one of the more disruptive problems an Electrolux owner can face. The noise is one issue, and the other is the risk of the machine working its way into a wall, cabinet or water connection over repeated cycles.
The good news is that the most common cause is also the easiest and cheapest to fix: the washer is not sitting level.
How do you level the washer correctly?
Front-load washers rely on four adjustable feet. Even a small amount of unevenness, enough that you might not see it just by looking, can let the spinning drum rock the whole cabinet instead of staying contained.
Place a level on top of the washer and check front to back and side to side. If it is off, adjust the feet by hand or with a wrench, then lock each one with its locknut so it does not drift back on the next heavy spin. The table below sums up the other usual causes.
| Sign | Likely cause | What you can check | When to call |
|---|---|---|---|
| Rocks when you push a corner | Feet not level | Level on top; adjust and lock feet | If it still rocks after leveling |
| Shakes only on an upper floor | Flexible floor | Floor bounce; anti-vibration pads | If pads do not help |
| New washer shakes hard | Shipping bolts still installed | Rear panel for leftover bolts | If bolts are out and it persists |
| Older washer walks on every load | Worn shock absorbers or springs | Drum sways more than before | Yes |
| Walks only with large items | Unbalanced load | Spread items evenly | No, unless it continues with small loads |
Can the floor cause the problem?
Yes. Even a perfectly level washer can walk on a flexible or springy floor, a common situation in upper-floor laundry rooms and older homes with less rigid subflooring. Anti-vibration pads under each foot can absorb movement that leveling cannot.
A washer pushed tight against a wall or cabinet, without the small clearance that installation guides recommend, can transmit vibration into nearby structures and make the problem seem worse than the machine’s actual motion.
What if it is not the feet or the floor?
If the washer is level, on solid flooring and still vibrates heavily, especially if this is new on a machine that ran fine for years, check whether the shipping bolts that hold the drum during transport were fully removed at installation. Left in place, they restrict the drum’s normal counterbalancing movement.
On an older washer, worn shock absorbers or a suspension spring that has lost tension let the drum swing farther than it should during spin, producing the same walking even when everything else is correct. These are repairs for a technician.
Why is it worth fixing promptly, and does the load matter?
A washer that walks repeatedly can gradually work its water supply hoses and drain connection loose, turning a vibration annoyance into a leak risk. It is better to address it sooner than to live with it, both for the washer and for whatever is installed around it.
An unbalanced load contributes as well. Redistribute large items such as towels or blankets before spinning. But a washer that walks consistently across different loads points at the machine and not at what is inside it.
Keep a simple log if the problem comes and goes. Note which loads cause the shaking, which spin speed it happens at and whether the washer has moved since the last time you checked. That helps separate a floor or leveling problem from a worn suspension part. Also check the water hoses and drain hose for tension after any walking, and make sure the washer has not pushed into the wall. Never run a washer that is violently shaking or hitting a wall.
Frequently asked questions
Is it normal for a front-load washer to vibrate a little?
Some vibration during the fastest spin is normal. Shaking that moves the washer, rattles the cabinet or shakes the floor is not. A level check is the first step in either case.
How tight should the locknuts be?
Tight enough that the feet cannot turn on their own during spin. Hold the foot steady with a wrench while you snug the locknut up against the cabinet. Recheck level after tightening, because it can shift.
Can I stack a dryer on a washer that walks?
Fix the walking first. A washer that moves under its own load puts stress on a stacked dryer and the connections. Follow your model’s installation guide for any stacking arrangement.
Do I need a technician for worn shock absorbers?
Yes. The suspension sits inside the cabinet and takes some disassembly. A technician can test it and replace the worn parts so that the drum stays balanced.