Standing water in the bottom of the tub after a finished cycle is most often caused by a clogged fine filter under the lower rack. Electrolux dishwashers are self-filtering, not self-cleaning, so the filter must be rinsed by hand. A cup or so of water near the filter is normal; a spreading pool is not and should be traced.
Why is there water in the bottom of my dishwasher?
Finding a puddle after a completed cycle looks like a serious drainage failure, but in a large share of cases the cause is within reach of most owners: the fine filter assembly beneath the lower rack.
Electrolux dishwashers, like most current designs, are self-filtering rather than self-cleaning. The machine circulates wash water through a fine mesh that catches food particles, but the filter does not flush itself. Left alone long enough, it clogs and slows or blocks the drain path, and water that cannot leave quickly sits in the base of the tub.
How do you check and clean the filter?
Turn off the dishwasher and remove the lower rack. On most Electrolux models the filter twists and lifts out of the bottom of the tub without tools. Rinse the assembly under running water and use a soft brush to loosen debris trapped in the mesh.
Then look at the opening where the filter sits. A piece of broken glass, a stray label or a seed can lodge in the drain opening itself. Cleaning the filter and clearing this spot resolves a meaningful share of water in the bottom complaints. The table summarizes the other likely causes.
| What you see | Likely cause | What you can check | When to call |
|---|---|---|---|
| A cup of water around the filter | Normal between cycles | Nothing needed | No call needed |
| Pool covering the tub floor | Clogged filter | Remove, rinse and brush the filter | If it returns after cleaning |
| Water returns after wiping | Debris in drain opening | Look under the filter seat | If the opening is clear |
| Slow drain with a gurgle | Kinked drain hose or blocked air gap | Hose behind the unit; air gap or high loop | If hose and air gap are clear |
| Cycle ends with standing water | Drain pump or sensor | Only after all checks above | Yes, have it tested |
What else can stop the dishwasher from draining?
If the filter is clean and water still pools, look behind the dishwasher at the drain hose. A kink or a pinch restricts drainage just as effectively as a clogged filter. Pull the unit out only if you can do so without straining the hoses, and switch off power at the breaker first.
If your installation has an air gap or a high loop under the sink, confirm that it is not blocked either. A blocked air gap or a hose that sags below the loop can let water back up toward the tub.
How much water is normal?
A small amount, generally no more than a cup or so around the base of the filter, is normal on most dishwashers between cycles and is not a sign of a problem.
A larger pool that covers the tub floor, or water that returns right after you wipe it up, points to a real drainage problem. Note whether it happens after every cycle or only after heavy loads, because that detail helps narrow down the cause.
How often should the filter be cleaned, and when does it point further?
Most households do well checking the filter every month or two. A home that runs the dishwasher daily, or washes pots and pans with heavy residue, should check more often. There is no downside to looking more frequently, and a routine is easier than remembering only after trouble starts.
With the filter, drain hose and air gap all clear, standing water points toward the drain pump or the SmartSoil sensor that helps decide when the cycle is complete. Both are technician-level repairs once the simpler causes have been ruled out.
Frequently asked questions
Can I run a cycle with water still in the bottom?
It is better to find the cause first. Clean the filter and check the drain hose, then run a short cycle. Repeating full cycles on a clogged drain can leave dirty water sitting in the tub and may spread debris around.
Is standing water in a dishwasher a leak?
Usually not. A leak shows up as water on the floor or inside the cabinet below. Standing water inside the tub is a drainage issue, though a long-term drainage problem can overload the tub and cause leaks, so do not ignore it.
Why does my dishwasher smell when water sits in it?
Water and food particles trapped in the base start to decay, which causes the odor. Cleaning the filter and fixing the drainage problem removes the cause. Odor that continues after cleaning means debris is still stuck somewhere in the drain path.
Do I need a tool to remove the filter?
Usually not. The filter on most Electrolux models twists and lifts out by hand once the lower rack is removed. If yours does not move easily, check the owner support page for your model instead of forcing it.