Troubleshooting

Reading F-Codes on an Electrolux Wall Oven

F-codes on an Electrolux wall oven point to a specific system, such as the temperature sensor, door lock or control board; note the exact code and when it appears.

An F-code on an Electrolux wall oven is the control board reporting that one of its systems is outside normal limits. F3 points to the temperature sensor circuit, F9 and F90 to the door lock, F10 to an over-temperature trip, and F13 to the control board processor. Write down the exact code and when it appears.

What do F-codes on an Electrolux wall oven mean?

Electrolux wall ovens show F-prefixed codes, such as F3, F9, F10 and F13, that come from the electronic oven control board monitoring its own systems. Unlike a vague report that the oven is not working, a code narrows the problem to a specific system.

That is useful as long as you read it correctly. It also tells you how safe the oven is to keep using while you wait for a repair. The table lists the four codes covered here, and the sections below explain each one.

What does F3 mean?

F3 points to a problem with the oven’s temperature sensor or the wiring that connects it to the control board. The sensor tells the oven how hot it is inside.

Do not just keep baking as usual. A failed sensor circuit means the displayed temperature may not reflect the real interior temperature, which affects your cooking results and, in the extreme, the oven’s ability to manage its own safety limits correctly.

Code System involved What you can check Next step
F3 Temperature sensor or its wiring Note whether results are off Technician; avoid regular baking
F9 or F90 Door lock Note whether it appeared during self-clean Technician; no more self-clean
F10 Over-temperature safety trip Do not clear and ignore it Technician before baking again
F13 Control board processor Power cycle at the breaker once Technician if it returns

What do F9 and F90 mean?

F9 and F90 relate to the door lock system and typically appear in connection with the self-clean cycle, which depends on the lock engaging correctly to keep the door sealed at very high interior temperatures.

If either code appears, especially during or after a self-clean attempt, do not run self-clean again until the oven has been checked. A lock that does not engage properly during that cycle is a real safety concern, not a minor inconvenience.

What does F10 mean?

F10 indicates the oven detected an interior temperature higher than it should be reaching for the current setting, and the control board cut power as a protective measure.

Do not clear this code and ignore it. An oven that has tripped this safety once should be checked before you bake with it again, because the underlying cause, often a relay or temperature sensor problem, does not resolve itself.

What does F13 mean, and can a reset help?

F13 points to the control board’s own internal processor, not a sensor or a mechanical part. Power cycling the oven can sometimes clear a one-time processor glitch: turn it off at the breaker, leave it for a few minutes, and switch it back on.

If F13 returns after that, the board itself has likely failed and needs replacement. Do not repeat the reset many times, and do not open the control panel. A processor error is also a good reason to note whether a power outage or surge happened shortly before the code appeared, since that detail helps a technician judge whether the board was upset by the power supply or has simply worn out.

What about other F-codes?

Electrolux documents additional codes beyond these four for its wall oven platform, covering things like specific relay failures and other sensor circuits, and the full list varies by model generation. The pattern across all of them is the same: the number after the F identifies a specific system.

Read the code against the documentation for your particular model, not against what a different oven generation uses. That keeps the diagnosis accurate. Whatever code you see, write it down exactly and note when it appears: during preheat, during self-clean or at random. Have your model number ready too, because the same code can mean something slightly different on another oven generation. If more than one code appears, record each one in the order it showed up.

Frequently asked questions

Can I clear an F-code myself?

Some codes clear when you switch the oven off at the breaker for a few minutes, but clearing is not fixing. If a code returns, or it is F10 or a door lock code, have the oven checked instead of resetting it repeatedly.

Is it safe to use the oven with an F-code showing?

It depends on the code. F3, F9, F90 and F10 all involve temperature control or door safety, so it is wiser to stop baking and self-cleaning until the oven has been checked.

Why does the code appear only during self-clean?

Self-clean pushes the oven to very high temperatures and relies on the door lock, so lock and temperature problems show up then. Note exactly when the code appeared, because it helps a technician narrow things down.

What should I tell the technician?

Give the exact code as shown, when it appeared, such as preheat, self-clean or at random, and your model number. Also mention whether the oven’s results have been off, which hints at sensor trouble.

Sources

Related Error Codes

Not Confident Doing This Yourself?

A trained technician can diagnose and fix it safely, usually same-day.

Need a repair? We're ready to help. Call Now
Call Us Schedule